Author: [email protected]

Crest Audio proudly introduces the new CM Series industrial power amplifiers, ideal for multi-channel applications in nightclubs, restaurants, hotels, retail stores and video conferencing systems.

The four-channel CM 2204 and eight-channel CM 2208 feature an advanced amplification architecture that allows low impedance or 70 Volt operation at the same power levels without switching. Each amplifier in the chassis will operate to rated power, regardless of impedance connected, from 4 Ohms to 70 Volt line systems. The design centers around an ultra-high efficiency output circuit, lowering the line current required for a given output power by as much as 50%. All inputs and outputs are on Phoenix(TM) connectors with level controls in the rear.

CM Series power amps include multiple protection circuits, such as ACL(TM) Active Clip Limiting, which automatically reduces gain at the onset of clipping to prevent amplifier and load damage; IGM(TM) Instantaneous Gain Modulation, which monitors load current to protect against overloading; AUTORAMP(TM) to prevent abrupt turn-on levels by gradually increasing gain when the amplifier is switched on; as well as short circuit, DC voltage, comprehensive thermal management, current in-rush turn on/off transient and sub/ultrasonic input.

A switch allows selection of 0.775V sensitivity or x40 gain. A high pass filter is selectable per channel, and 100 Volt and 50 Volt operation is supported with our CM100V and CM50V accessories.

The CM Series will be available in Q1 2005 from authorized Crest Audio dealers.

CM 2204

• 160 Watts x 4 (4 Ohm output)
• 220 Watts x 4 (70 Volt output)
• 240 Watts x 4 (8 Ohm output)
• Frequency Response: 20 Hz to 20 kHz
• Cooling via DC fan, front-to-side air flow
• Balanced, three-pin Phoenix inputs
• Two-pin Phoenix outputs
• Signal, clip and protect LED indicators
• 16-gauge steel chassis
• Two rack spaces
• 27 lbs.
• U.S. MSRP $TBA

CM 2208

• 160 Watts x 8 (4 Ohm output)
• 220 Watts x 8 (70 Volt output)
• 240 Watts x 8 (8 Ohm output)
• Frequency Response: 20 Hz to 20 kHz
• Cooling via DC fan, front-to-side air flow
• Balanced, three-pin Phoenix inputs
• Two-pin Phoenix outputs
• Signal, clip and protect LED indicators
• 16-gauge steel chassis
• Two rack spaces
• 35 lbs.
• U.S. MSRP $TBA

Crest Audio proudly introduces the new CD Series power amplifiers, the new generation of elevated-efficiency amplification from Crest Audio.

The CD Series combines a linear power supply with a Class D output to deliver legendary Crest power in a compact, cost-effective package, with an efficient output stage to allow the power supply to handle heavy duty cycles without compromising sonic integrity. Versatile power points, multiple inputs and other features make the CD Series adaptable to nightclubs and high school gymnasiums alike, and every application between. With the CD Series, sonic performance is the primary objective. CD Series power amps include multiple protection circuits such as ACL™ Active Clip Limiting, which automatically reduces gain at the onset of clipping to prevent amplifier and load damage; IGM(TM) Instantaneous Gain Modulation, which monitors load current to protect against overloading; AUTORAMP(TM) to prevent abrupt turn-on levels by gradually increasing gain when the amplifier is switched on; as well as short circuit, DC voltage, comprehensive thermal management, current in-rush turn on/off transient and sub/ultrasonic input. The CD Series will be available in Q1 2005 from authorized Crest Audio dealers.

CD-3000

• Stereo Mode, 8 Ohms: 800 Watts
• Stereo Mode, 4 Ohms: 1500 Watts
• Stereo Mode, 2 Ohms: 1500 Watts
• Bridged Mode (mono), 8 Ohms: 3000 Watts
• Bridged Mode (mono), 4 Ohms: 3000 Watts
• 85 Volts RMS max output voltage
• Frequency Response: 20 Hz to 20 kHz
• Cooling via back-to-front, variable-speed DC fan
• Inputs: balanced female XLR, 1/4″ TRS, unbalanced 1/4″ TS on Neutrik combi connectors
• Outputs: five-way binding posts and Speakon® connectors
• Signal (five-level bar graph), active, ACL/IGM and protect LED indicators
• 16-gauge steel chassis, cast aluminum front panel
• Two rack spaces
• 41.4 lbs.
• U.S. MSRP $TBA

CD-2000

• Stereo Mode, 8 Ohms: 560 Watts
• Stereo Mode, 4 Ohms: 1000 Watts
• Stereo Mode, 2 Ohms: 1000 Watts
• Bridged Mode (mono), 8 Ohms: 2000 Watts
• Bridged Mode (mono), 4 Ohms: 2000 Watts
• 72 Volts RMS max output voltage
• Frequency Response: 20 Hz to 20 kHz
• Cooling via back-to-front, variable-speed DC fan
• Inputs: balanced female XLR, 1/4″ TRS, unbalanced 1/4″ TS on Neutrik combi connectors
• Outputs: five-way binding posts and Speakon connectors
• Signal (five-level bar graph), active, ACL/IGM and protect LED indicators
• 16-gauge steel chassis, cast aluminum front panel
• Two rack spaces
• 38 lbs.
• U.S. MSRP $TBA

CD-1500

• Stereo Mode, 8 Ohms: 400 Watts
• Stereo Mode, 4 Ohms: 750 Watts
• Stereo Mode, 2 Ohms: 750 Watts
• Bridged Mode (mono), 8 Ohms: 1500 Watts
• Bridged Mode (mono), 4 Ohms: 1500 Watts
• 64 Volts RMS max output voltage
• Frequency Response: 20 Hz to 20 kHz
• Cooling via back-to-front, variable-speed DC fan
• Inputs: balanced female XLR, 1/4″ TRS, unbalanced 1/4″ TS on Neutrik combi connectors
• Outputs: five-way binding posts and Speakon connectors
• Signal (five-level bar graph), active, ACL/IGM and protect LED indicators
• 16-gauge steel chassis, cast aluminum front panel
• Two rack spaces
• 35 lbs.
• U.S. MSRP $TBA

CD-1000

• Stereo Mode, 8 Ohms: 280 Watts
• Stereo Mode, 4 Ohms: 500 Watts
• Stereo Mode, 2 Ohms: 500 Watts
• Bridged Mode (mono), 8 Ohms: 1000 Watts
• Bridged Mode (mono), 4 Ohms: 1000 Watts
• 53 Volts RMS max output voltage
• Frequency Response: 20 Hz to 20 kHz
• Cooling via back-to-front, variable-speed DC fan
• Inputs: balanced female XLR, 1/4″ TRS, unbalanced 1/4″ TS on Neutrik combi connectors
• Outputs: five-way binding posts and Speakon connectors
• Signal (five-level bar graph), active, ACL/IGM and protect LED indicators
• 16-gauge steel chassis, cast aluminum front panel
• Two rack spaces
• 30 lbs.
• U.S. MSRP $TBA

Crest Audio proudly introduces its new CC Series of power amplifiers, the CC 4000, CC 2800 and CC 1800. Based on powerful Crest Pro 200(TM) Series technology and utilizing a linear power supply, our versatile CC Series amps deliver stable high power output for running main systems, monitors and subwoofers.

Building upon the solid foundation of legendary Crest Audio amplifier designs, CC Series power amps provide tremendous value in proven amplifier technology. CC Series amps deliver world-class power with exceptional sound quality and value for mobile DJs, working bands, club owners, churches and more. Utilizing several new production techniques and Crest-designed toroidal transformers for steady, beefy output that is lightweight in design, the CC Series exemplifies the Crest tradition for solid, reliable and innovative power amp designs.

All CC Series amplifiers are built with tunnel-cooled heat sinks, variable-speed DC fans and extensive protection circuitry for superior efficiency into difficult loads and power conditions. In the Crest Audio tradition, the CC 4000 and CC 2800 also boast more power devices (16 per channel) than any competitive amplifier, plus a switched-rail class H output stage and triple-compound design to provide low distortion and excellent thermal stability.

The CC Series will be available in April 2005 from authorized Crest Audio dealers.

Crest Audio proudly introduces its new Nx CobraNet-8(TM) control module and CMi Series power amplifiers, which work in tandem to support Crest NexSys 4 and Peavey MediaMatrix(R) MWare(TM) software programs for advanced control and audio routing.

The Nx CobraNet-8 module, which fits into the rear bay of CMi 2204 and CMi 2208 power amps, supports all NexSys functions, DSP functions and CobraNet digital audio I/O on a single CAT 5 Ethernet cable. A four-character LED allows easy setup, control and monitoring of up to eight CobraNet audio channels from the rear panel of the CMi power amps, which ship network ready.

An extensive suite of DSP options including delay, EQ, compression/limiting and crossover adds to the functionality of the Nx CobraNet-8 module. Amplifier monitoring includes ACL(TM), IGM(TM), input/output gain (VU), DC, thermal protect, fault, mute, Ethernet data and link statuses.

The four-channel CMi 2204 and eight-channel CMi 2208 power amps feature an advanced amplification architecture that allows low impedance or 70 volt operation at the same power levels. Each amplifier in the chassis will operate to rated power, regardless of impedance connected, from 4 ohms to 70 volt line systems. The design centers around an ultra-high efficiency output circuit, lowering the line current required for a given output power by as much as 50%. All inputs and outputs are on Phoenix(TM) connectors with level controls in the rear. In addition, a Control Voltage input is included on each channel to allow external gain control, while the Fault output on each channel allows the CMi power amps to be wired to other monitoring systems.

Crest Audio’s exclusive ACL (Active Clip Limiting) automatically reduces gain at the onset of clipping to prevent amplifier and load damage, while IGM (Instantaneous Gain Modulation) monitors load current to protect against overloading. When used in conjunction with the external Crest Audio CMX accessory, CMi power amps will also support 100V and 50V operation. Both the Nx CobraNet-8 module and the CMi 2204 and 2208 are backed by Crest Audio’s strong five-year warranty.

The Nx CobraNet-8 module and CMi power amps will be available in 2005 from authorized Crest Audio dealers.

CMi 2204 Power Ratings

• 150W per channel at 4 ohms
• 225W per channel at 8 ohms
• 300W per bridged channel at 8 ohms bridged
• 220W per channel at 70V
• 440W per channel at 140V

CMi 2208 Power Ratings

• 150W per channel at 4 ohms
• 220W per channel at 8 ohms
• 300W per bridged channel at 8 ohms bridged
• 200W per channel at 70V
• 400W per channel at 140V

Peavey Electronics Corporation announces it has consolidated the Crest Audio manufacturing and business office in Fair Lawn, N.J., to its international headquarters in Meridian, Miss.

Hartley Peavey, founder and CEO of Peavey, cited market demand for products, especially in export markets, as the major reason for the move. The Crest Audio and Crest Performance product lines have experienced significant sales increases during 2004 and early 2005.

“In many cases, we had duplicate systems and overlapping operations in Mississippi and New Jersey that were unnecessary and costly to maintain,” commented Peavey. “We are now incorporating the best methods from both operations to give us faster time-to-market and reduced costs, which will benefit both the company as well as Peavey and Crest Audio consumers.”

With the recent addition of Meridian-based sales and marketing personnel for Crest Audio and the addition of more than 150 people to the Meridian manufacturing workforce, this move will enhance the Crest Audio operation significantly. Many of the subassemblies for Crest Audio’s world-class mixing consoles and power amps products are already in production at Peavey’s Decatur, Miss., facility.

Although Peavey and Crest Audio now share manufacturing and distribution resources, the companies will remain largely autonomous, with separate sales, design, engineering and management staffs. Crest Audio will continue to operate as a division of Peavey Electronics Corporation alongside the Architectural Acoustics(R), MediaMatrix(R) and PVDJ(TM) brands. Peavey acquired Crest Audio in 1998.

Crest Audio proudly introduces the HP-W professional mixing console, a continuation of its celebrated, feature-packed HP-Eight™ Series consoles. The HP-W is available in 28-, 36- and 44-standard mono input frames—with four full stereo channels, eight mono Automix™ channels and two stereo line returns—making this console ideal for both mixed music and spoken word applications.

The HP-W mixing console combines Crest Audio’s legendary sound and build quality with sought-after features such as four-band, double-swept mid EQ; eight analog subgroups; 100 mm faders; two-channel matrix; full talkback and monitor systems; and eight-scene mute. This quality console also includes 10 aux sends on each input channel with fader flip functions for use as a monitor mixer, plus four stereo line input channels with EQ, assignment and aux sends capable of handling dual-mono or split-track signals.

Also standard on all HP-W consoles are eight mono channels of Automix for “hands-off” spoken word mixing. Automix is a gain-sharing protocol that allows increased gain before feedback. Engaging the Automix priority switch will greatly reduce comb filtering by turning down unused or low priority inputs. HP-W consoles also include four stereo channels, a stereo ambient mic input and two alternate outputs with processing.

The HP-W will be available in Q1 2006 from authorized Crest Audio dealers.

Features

• 44, 36 or 28 standard mono input channels
• Eight analog subgroups
• 10 auxes
• Eight mono gain-sharing Automix(TM) input channels
• 11 x 2 matrix
• Four fully stereo input channels with assignments that can also handle dual-mono or split- track applications
• Two stereo line returns on 60 mm faders with assignment and two aux sends
• One stereo ambient mic input with four aux sends
• XLR and ¼” connectors on all mono inputs
• Individual 48-volt phantom power, mic/line and polarity reverse switches on all mono input channels
• Fader Flip function on aux outputs places aux masters on 100 mm faders in place of groups & L/R
• 100 mm high-quality faders on mono inputs, auto mix inputs, stereo inputs, groups and separate left, right and mono outputs
• Four-band, double-swept mid EQ
• Eight microprocessor-controlled mute scenes
• Full talkback and monitor systems
• Two alternate outputs that can be sourced from L, R, M or matrix outputs (stereo compressor, expander and limiter on both)
• XLR connectors on aux outputs
• Full talkback and monitor systems
• Internal power supply with provision for external, redundant supply
• Modular input blocks of eights channels for ease of service
• Made in the U.S.A.
• U.S. MSRP $TBA

Crest Audio proudly introduces the Ci Series power amplifiers, which are geared to meet the demanding networking needs of modern systems integrators. Ci amps can operate independently or in tandem with Crest NexSys(R) 4 or Peavey MediaMatrix(R) software programs.

The four-channel Ci 20×4 and eight-channel Ci 20×8 power amps feature an advanced amplification architecture that allows 200 watts per channel at 8-ohm or 70-volt operation. Each amplifier in the chassis will operate to rated power, regardless of impedance connected, from 4 ohms to 70-volt line systems, switchable per channel (100-volt isolated outputs with optional CMX 100-volt isolation transformer unit).

With the addition of Crest Audio’s module bay accessories, such as the new Nx CobraNet-8(TM), users can monitor and control networks through Crest Audio NexSys 4 software or MediaMatrix MWare(TM) or NWare(TM) software. All inputs and outputs are on Phoenix(TM) connectors with level controls in the rear. In addition, a Control Voltage input is included on each channel to allow external gain control, while the Fault output on each channel allows the Ci Series power amps to be wired to other monitoring systems.

Crest Audio’s legendary Tour Class(R) protection suite includes exclusive ACL(TM) (Active Clip Limiting), which automatically reduces gain at the onset of clipping to prevent amplifier and load damage, and IGM(TM) (Instantaneous Gain Modulation), which monitors load current to protect against overloading. These amplifiers also feature Sequential Turn-On, one Form C latching relay per channel and one CV input per channel.

Please see your authorized Crest Audio representative for availability and pricing. Features and specifications are subject to change without notice.

Ci 20×8

• 150 watts per channel at 4 ohms x 8
• 220 watts per channel at 8 ohms x 8
• 200 watts per channel at 70-volt x 8
• 300 watts per channel at 8 ohms bridged x 4
• 400 watts per channel at 140-volt bridged x 4
• Five-year warranty
• Made in the U.S.A.

Ci 20×4

• 150 watts per channel at 4 ohms x 4
• 220 watts per channel at 8 ohms x 4
• 200 watts per channel at 70-volt x 4
• 300 watts per channel at 8 ohms bridged x 2
• 400 watts per channel at 140-volt bridged x 2
• Five-year warranty
• Made in the U.S.A.